How to Hang a Frameless Mirror on a Wall Tips
Moving from one house to another comes with many challenges, and whether big or small, you will have to deal with them. However, the entire moving process has been made easier by removals in Bicester, a reliable company in the UK, so you can relax and deal with other small challenges such as hanging a frameless mirror in your new home you’ve just moved in.
While the everyone will tell you the frameless mirror looks best only on the bathroom wall, but you can simply hang a wall mirror in other parts of your house too, and watch the entire look of your room change. A frameless wall mirror is good on any type of house decor. As such, you can hang it on as many places in your house as you want, provided you don’t go overboard with it.
Now, the act of hanging a full length wall mirror that is framed involves the same procedure one follows for picture frames. Frameless mirror requires a different sort of technique. If you’re about to custom order your new round wall mirror- or maybe you’re simply going for a large wall mirror- it’s time you’re prepared with the knowledge on how to hang a frameless mirror on a wall.
Now a days, hang a frameless mirror on a wall is too much popular interior work. There are many ways to make this job. However to do this perfectly, it is important to know the different types of walls and uses essential tools. Here we discussed the most effective and simple method for you.
Hang a Frameless Mirror on a Wall help guide
Step 1: Identify and Mark the Exact Spot
You must have specific areas around your house where you think the mirror would look best. The first step would be to identify those exact spots. Take the mirror out and hold it up against the wall in the position you want it to adorn. Grab a pencil or a marker and take note of the bottom and top corners of the mirror. You can now place the mirror back in its place.
It would be easier to go through this step if you have someone to help you on the side. You can either hold the mirror and ask the person to do the marking or vice versa.
If the frameless mirror you have is small, use clips. If the mirrors are large, use Z-clips which can hold lots of weight.
Step 2: Make Sure It’s Straight
The next process would be to make sure you actually hang the mirror straight. To get the exact measurements, grab a spirit level and place it against the marking of the top and bottom corner. Do you know how to use a spirit level? It’s pretty simple. The bubble in the tube should go equally between the black lines. If it’s off, you need to adjust the level until the bubble realigns at the center
Step 3. Check The Wall to See If It’s Flat or Not
Or that is, check whether the wall is flat or not. If the wall where you’re going to place the mirror is bumpy in some spots, trying to clip a mirror against it securely can actually cause the wall to crack.
How to locate a random bump on an otherwise flat wall you might ask? Grab a straight-edged board, preferably something that is longer than the mirror. It’s best if you have a yardstick, otherwise, you can go for lumber of about one inch you know it straight.
Slide it over the wall and if it spots the bump, you will get an immediate response. Mark the bumpy spots with a pencil. You can either hang the mirror on another part of the wall or sand it down. You can go for the power sander method, which would be the quickest. You can sand by wrapping sandpaper around a wooden block too.
Step 4: Mark The Edges of the Studs
Usually, pretty much behind every interior wall in people’s homes, workers place studs. These are a kind of evenly spaced wooden beams that help support the wall. You can locate the studs without any extra effort by sliding an automatic stud finder across the wall. Use a pencil to mark the edges of the stud around the outer area.
Of course, it leaves the question of what to do if you do not have a stud finder. Well, there is another just as effective but time-consuming method. In this case, you can get an exact idea of the stud by tapping the wall on where you want to hand the mirror. If the taps sound solid, that is a very clear hitting against the brick sound, there isn’t a stud there. If it sounds hollow, like there’s air there, the stud is located in the exact area.
Take a step back and check where it leaves the mirror to be positioned once you find the studs. If the mirror is positioned in a way that it actually covers the stud with its body, you need to shift it. The goal is to find an area where the clip and stud can be screwed together.
Step 5: Start Drilling Pilot Holes
You can’t go through this step without a drill. Please make sure you have a drill ready beforehand before you begin this procedure. You are especially going to need a power drill. Grab the power drill and place it over the locations you have marked. Now, turn it on and start drilling holes into the area.
